Explorar categorias
Fuente de alimentación conmutada WAGO 787-1632/000-070
Descripcion
WAGO 787-1632/000-070 suministra una salida de 24 V DC a 10 A y se monta en carril DIN de 35 mm.
Especificaciones
| Brand | WAGO |
|---|---|
| MPN | 787-1632/000-070 |
| HS Code | 850440 |
| Connection type | Input/output/signaling |
| Inrush current | ≤ 30 A |
| Input voltage range | 1 x 85 … 264 VAC; 100 … 300 VDC |
| Power factor correction (PFC) | Active |
| Power loss (max.) Pl (max.) | 31.3 W (100 VAC / 24 VDC; 10 A) |
| Power loss Pl | ≤ 6.6 W; ≤ 24.4 W (230 VAC; nominal load) |
| Nominal mains frequency range | 44 … 66 Hz; 0 Hz |
| Output voltage range | 23 … 28.5 VDC (adjustable) |
| Weight | 1140 g |
| Relative humidity | 5 … 96 % (no condensation permissible) |
| Ambient temperature (operation) | -25 … +70 °C (Device starts at -40 °C (type-tested)) |
| Ambient temperature (storage) | -25 … +85 °C |
| Backup fuse (recommended) | Circuit breaker: 10 A, 16 A; Tripping characteristic: B or C |
| Climatic category | 3K3 (per EN 60721) |
| Conformity marking | CE |
| Connection technology | CAGE CLAMP® |
| Current limitation | 1.1 x Io nom (typ.) |
| Default Setting | 24 VDC |
| Depth from upper-edge of DIN-rail | 172 mm / 6.772 inches |
| Derating | -5 %/K (> 60 °C, 196 … 264 VAC); -2.5 %/K (> 50 °C, 85 … 195 VAC) |
| Deviation | ≤ 1 % |
| Eccn | NO US CLASSIFICATION |
| eCl@ss 10.0 | 27-04-07-01 |
| eCl@ss 9.0 | 27-04-07-01 |
| Efficiency (typ.) | 91 % |
| ETIM 10.0 | EC002540 |
| ETIM 9.0 | EC002540 |
| Fine-stranded conductor | 0.08 … 2.5 mm² / 28 … 12 AWG |
| Fire load | 0.267 MJ |
| Height | 127 mm / 5 inches |
| Input current Ii | ≤ 1.25 A (230 VAC); ≤ 2.74 A (100 VAC) |
| Input voltage derating | -2.5 %/V (< 100 VAC); -1 %/V (< 130 VDC) |
| Internal fuse | T 6.3 A / 250 VAC |
| Isolation voltage (pri.-PE) | 2.2 kVDC |
| Isolation voltage (pri.-sec.) | 4.242 kVDC |
| Isolation voltage (sec.-PE) | 0.7 kVDC |
| Mains failure hold-up time | ≥ 17 ms (230 VAC); ≥ 15 ms (100 VAC) |
| Mounting type | DIN-35 rail |
| Mtbf | > 500,000 h (per IEC 61709) |
| Nominal input voltage Ui nom | 1 x 100 … 240 VAC |
| Nominal output current Io nom | 10 A (24 VDC) |
| Nominal output power | 240 W |
| Nominal output voltage Uo nom | 24 VDC (SELV) |
| Open-circuit-proof | Yes |
| Operation status indicator | Green LED (Uo) |
| Overload behavior | Constant current |
| Overvoltage category | II |
| Overvoltage protection; secondary | Internal protective circuit; ≤ 40 VDC (in the event of a fault) |
| Parallel operation | Yes |
| Phases | 1 |
| Pollution degree | 2 |
| Pre-fuse (required) | An external DC fuse is required for the DC input voltage. |
| Protection class | I |
| Protection type | IP20; per EN 60529 |
| Protective coating | Coated PCBs |
| PU (SPU) | 1 pcs |
| Residual ripple | ≤ 50 mV (peak-to-peak) |
| Resistance to reverse feed | ≤ 35 VDC |
| RoHS Compliance Status | Compliant,No Exemption |
| Series operation | Yes |
| Short-circuit-protected | Yes |
| Signaling | 1 x DC OK LED (green); 1 x DC OK contact (make contact; max. 30 VAC/DC; 1 A) |
| Solid conductor | 0.08 … 2.5 mm² / 28 … 12 AWG |
| Standards/specifications | EN 61010-1; EN 61010-2-201; EN 61204-3; UL 60950-1; UL 508 |
| Strip length | 8 … 9 mm / 0.31 … 0.35 inches |
| Topboost | See instruction leaflet |
| Transient suppression (primary) | Varistor |
| Unspsc | 39,121,004 |
| WAGO connector | WAGO 721 Series |
| Width | 55 mm / 2.165 inches |